Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for San Clemente Homeowners
Gate repair in San Clemente typically runs $150 to $450 for most residential fixes, while electric operator and control board work lands between $300 and $900 depending on the system. A gate that won’t open, grinds when it moves, or sags on its hinges is not a weekend project, it’s a security and access problem that gets worse the longer it sits. Oscar Jarvis and the Gate Repair San Clemente team respond fast across San Clemente because a stuck gate locks you in or out of your own property. We diagnose most brands over the phone before the truck rolls, and our quotes are always agreed before any work starts. Call (866) 282-7403 for a free estimate and same-day service on most repairs.
Driveway Gate Repair
Driveway Gate Repair is what we handle most often in San Clemente, where coastal salt air accelerates wear on hinges, wheels, and operator motors faster than inland neighborhoods. A driveway gate that drags on the concrete, buzzes without moving, or only opens when you hold a remote at a certain angle needs a specialist who already knows your brand’s failure patterns. We repair swing and slide driveway gates, replace worn hardware, recalibrate limits, and diagnose motor and control board issues on Ghost Controls, Mighty Mule, Elite, and heavier commercial residential systems. Most driveway gate repairs in San Clemente run $150 to $450, with motor replacement at $400 to $900 depending on operator type and access, which you can learn more about in our Gate Repair pricing breakdown. We quote the full price before any work begins, so you never see a surprise invoice.
Won’t Open or Close Fully
The most common driveway gate complaint. Limit switch drift, sensor misalignment, or a failing capacitor usually causes it. We reset travel limits and test under load so the fix holds, not just for a day.
Remote or Keypad Not Working
Often the receiver board or antenna, not the remote itself. We test signal strength, replace failing boards with brand-correct parts, and reprogram remotes and keypads on the spot.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding is required when structural damage goes beyond what a bolt or bracket can hold: cracked frames, snapped hinge welds, torn posts, or sections that have pulled apart from years of wind load and use. In San Clemente’s salt-heavy coastal air, untreated cracks turn into complete failures quickly, and a gate that collapses poses a real safety hazard. We do on-site welding for iron, steel, and aluminum gates, re-square frames that have racked from sagging, and reinforce weak points rather than just patching them. Typical gate welding repairs in San Clemente run $200 to $600 depending on the number of repair points and whether the gate needs removal and resetting. We always quote the job before striking an arc, with no hidden fees after the fact.
Cracked Frame or Broken Hinge
We grind out the crack, weld it properly, and add reinforcement plate where the original design left a weak spot. A surface patch without grinding will crack again within months. That’s the difference between a cosmetic repair and one that lasts.
Gate Pulled Away From Post
Common on heavy iron gates where the post has shifted or the original weld was under-sized. We re-weld, reinforce the mount plate, and reset the gate so it hangs square and swings without binding.
Commercial Gate Repair
Commercial Gate Repair in San Clemente means getting a property’s access point back online today, not scheduled for next week. Retail centers, HOAs, storage facilities, and industrial lots depend on their gates for security and traffic flow, and a down gate backs up cars and opens the property to anyone. We service commercial operators including DoorKing, FAAC, BFT, LiftMaster, and Viking, and we stock or can source parts for these systems faster than a generalist who has to research the unit on-site. Most commercial service calls in San Clemente run $250 to $900 depending on whether it’s a limit adjustment, a loop detector replacement, or a motor and control board swap. We arrive with the diagnostic gear to test loop continuity and circuit function, give you a written quote, and get the gate moving again, usually the same visit. For homeowners nearby, we also offer Gate Repair – San Juan Capistrano with the same rapid response.
Slide Gate Off Track or Stuck
Commercial slide gates bear daily abuse. We replace worn guide rollers, reset track alignment, and rebuild chain or belt drives so the gate travels smoothly and stops where it’s supposed to.
Loop Detector and Safety Sensor Issues
A gate that won’t close or reverses randomly is often a failed loop detector or a photo-eye alignment issue. We test, replace, and configure detectors to the specific commercial operator, including DoorKing and FAAC boards that require exact settings.
Iron Gate Repair
Iron Gate Repair covers the structural and cosmetic restoration of solid iron gates, from hinge replacement to weld repairs to rust treatment that stops corrosion at the source. San Clemente’s marine layer means iron gates here rust faster than they would ten miles inland, and a gate that looks rough is usually structurally weak under the paint. We handle sag corrections, hinge pin and bearing replacement, weld-in replacement sections, and rust treatment with proper priming and coating. Most iron gate repairs in San Clemente run $150 to $500, with more involved structural work like frame re-welding landing at $400 to $700. We quote the job in writing before starting, so you know exactly what a repair costs before you commit.
Sagging or Dragging Corner
Usually a failed top hinge bearing or a frame that has started to rack. We replace the hinge with an appropriately rated bearing hinge and re-square the frame so the gate closes without lifting it.
Rust Through on Frame Members
Rust never sleeps in coastal air. We cut out rotted sections, weld in new material, and finish with rust-inhibiting primer so the repair doesn’t become a new rust point in two years.
Sliding Gate Repair
Sliding Gate Repair addresses gates that roll on tracks, cantilever systems, and motor-driven slide operators that have stopped traveling correctly. The most common issues we fix in San Clemente are seized wheel bearings from coastal grit, broken chain or belt drives, and motors that strain because the track has shifted. We align track, replace rollers and guide wheels, repair or replace drive chains, and recalibrate travel limits so the gate stops where it should. Sliding gate repairs in San Clemente typically run $200 to $600, with motor replacement costs running $500 to $900 for heavier operators like DoorKing or LiftMaster commercial models. Prices are agreed before work starts every time, and estimates are free.
Gate Grinds or Shakes When Moving
That sound is almost always worn guide rollers or bearings that have been eaten by sand and salt. We replace the rolling hardware, lube the points that need it, and verify alignment so the gate glides instead of grinding.
Operator Runs But Gate Doesn’t Move
Usually a stripped drive gear, snapped chain, or broken solenoid in the operator. We diagnose which component failed, replace it with a brand-correct part, and test the full travel cycle before we leave.
Wrought Iron Gate Repair
Wrought Iron Gate Repair focuses on ornamental and decorative iron gates, the kind common in older San Clemente neighborhoods and custom home entries. These gates fail differently from plain steel: the ornamental work hides cracks, the scrollwork collects moisture, and the fine welds from original fabrication let go after decades near salt air. We repair broken scrolls, re-weld decorative elements, replace ornamental hinge straps, and match the original design so the repair doesn’t look like a patch. Most wrought iron repair work in San Clemente runs $200 to $600, with extensive ornamental restoration at $500 to $900. You’ll get an exact price before we start, and we won’t charge you to come out and take a look.
Broken or Missing Scrollwork
We fabricate replacement scrolls to match the existing pattern, then weld and finish them so they read as original. Leaving a scroll off weakens the adjacent sections and collects rust in the broken welds.
Hinges Seized or Bent
Wrought iron gates are heavy, and a bent hinge means the gate now hangs off its original load path. We replace with forged or fabricated hinges that match the visual weight and carry the load properly.
Metal Gate Repair
Metal Gate Repair is the broadest category we handle, covering steel, aluminum, and iron gates in residential and light commercial settings. Whether you have a modern aluminum slat gate, a powder-coated steel pedestrian gate, or a farm-style tube gate, the failure tends to be mechanical: hinge wear, latch misalignment, weld cracks, or bowing from impact. We straighten frames, replace hardware with weather-rated components suited to San Clemente’s salt environment, and handle latch and lock integration so the gate actually secures. Typical metal gate repairs range from $150 to $500, with more involved frame or weld work at $400 to $700. Quote first, always, and the price we quote is the price you pay.
Gate Won’t Latch or Lock
Most often a shifted post or a latch that’s worn past engagement. We reset the post or replace the latch with a marine-grade unit that holds up to coastal corrosion and still closes quietly.
Frame Bowed or Twisted
A twisted metal gate won’t ever close right until the frame is corrected. We assess whether heat-straightening or section replacement makes more sense, then do the repair that lasts.
Wood Gate Repair
Wood Gate Repair in San Clemente involves both the wood structure and the hardware that carries it. Coastal moisture rots wood stiles and rails at the bottom and around hinge mounts, and once a hinge pulls out of rotted wood, the gate drops and drags. We replace rotted stiles and rails with pressure-treated lumber or cedar, rebuild hinge mortises with proper depth and hardwood blocking, and re-hang the gate so it swings clean and latches securely. Most wood gate repairs run $180 to $450, with more extensive rebuilds at $400 to $700. We quote before cutting anything, and we won’t sell you a new gate when a rebuild is the honest fix.
Sagging or Scraping
Wood gate sag is usually hinge failure in rotted wood, not the wood itself. We rebuild the hinge points, replace worn hinges, and re-square the gate so it moves freely without dragging.
Rotted Rails or Stile Bottoms
We cut back to sound wood, splice in new material with weather-rated adhesive and hardware, and seal the end grain so water doesn’t wick back into the repair.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We service Ghost Controls and Mighty Mule residential openers regularly, which are the two most common systems on San Clemente driveways. That means we know their control board failure modes, their remote programming quirks, and which limit adjustments stop the gate from slamming or stopping short. We also work extensively with Elite and DoorKing operators, both residential and commercial, including the heavier cantilever and slide applications where an under-specified repair just won’t hold.
Our brand coverage means you don’t get a technician who reads the manual in your driveway. We arrive with brand-specific knowledge of what fails on these systems, which replacement parts are compatible, and how to set limits and force settings the way the manufacturer intended. Whether you have Ghost Controls, DoorKing, Elite, Mighty Mule, or any other make, we can help.
Signs You Need a Pro Right Now
- Gate only opens when you hold the remote at a specific angle. This is almost always a failing receiver board or antenna. It’s intermittent now, but the next failure is usually permanent, and it happens when you’re outside the gate. A quick board test confirms it.
- The gate hesitates or reverses randomly while closing. Safety edge or photo-eye problems cause this. Ignoring it means a gate that eventually refuses to close at all, or worse, closes when it shouldn’t. Both are liability issues on a shared driveway.
- You hear grinding or squealing when the gate moves. Metal-on-metal noise means bearings, rollers, or gears are already wearing. The longer it grinds, the more collateral damage builds inside the operator, and a $200 roller replacement becomes a $600 motor rebuild.
- The gate sags and you have to lift it to close it. A sagging gate is tearing its hinges or stressing the operator motor every single cycle. Each opening makes the repair more extensive, and the gate still has to be fixed before it can be automated again.
- Visible cracks in welds, hinge plates, or frame members. Cracks aren’t cosmetic on a moving gate. They’re load paths that have already failed. A cracked weld under stress will separate completely, and a broken gate falling onto a car or person is a serious problem.
Our Process, Step by Step
- 1
Call and describe what’s happening. You talk to a person who knows gates, not a call center. Based on the symptoms, the brand, and whether the gate is electric or manual, we often have a strong diagnosis before we even arrive, which means the right parts are on the truck.
- 2
We arrive and confirm the diagnosis. We test the operator, inspect the structure, check hinges, wheels, tracks, loop detectors, and control boards. We use multimeters and loop testers to see what’s actually failed, not just guess.
- 3
You get a written quote before any work starts. We show you the repair scope, the parts cost, the labor, and the total. If you approve, we do the work. If you don’t, you owe nothing for the visit and you know exactly what the gate needs.
- 4
We repair and test everything. Structural repairs get welded and checked for square. Electric systems get limits set, force settings calibrated, and safety devices verified. We test the gate through multiple full cycles, not once.
- 5
We walk you through what was done and what to watch. You’ll know what broke and why, how to tell if it’s coming back, and whether any preventative work makes sense. You’ll also know the gate is back to working before you know it, and that the repair was done right the first time.
How Much Does Gate Repair Cost in San Clemente?
A typical gate repair in San Clemente runs $150 to $450 for hardware fixes like hinge replacement, latch repair, roller swaps, and limit adjustments. For a deeper look at symptoms and solutions, see The Complete Gate Repair Guide for San Clemente Homeowners. Electric gate repair involving control boards, loop detectors, or motor replacement lands in the $300 to $900 range depending on the operator brand and whether it’s a residential or commercial system. Structural work like gate welding or frame straightening runs $200 to $600 for most jobs, while full ornamental wrought iron restoration can reach $900.
What affects the price: the gate’s weight and material (wrought iron and heavy steel take longer), the operator’s age and brand (some boards cost more than others), whether the gate is accessible from both sides, and whether we’re repairing or replacing a component. You avoid overpaying by working with a company that stocks and knows multiple brands, because a specialist doesn’t charge you to diagnose a system they already know. Our estimates are always free, and the price we quote before work starts is the price on your invoice. Call (866) 282-7403 for an exact quote.
Our Service Area Near San Clemente
We serve San Clemente and the surrounding South Orange County communities, including Gate Repair in Mission Viejo, Gate Repair in Laguna Niguel, San Juan Capistrano, Dana Point, and Rancho Santa Margarita. For most neighborhoods in San Clemente and the immediate coast, we can often be on-site the same day. Whether you’re near the pier, up in Forster Ranch, or out toward Talega, call (866) 282-7403 and we’ll get you scheduled. You can also check our home page or the main Gate Repair in San Clemente page for more detail.
Serving San Clemente, CA – Our Local Coverage Area
We’re based in the San Clemente area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in San Clemente
Gate repair is any work that returns a damaged or malfunctioning gate to proper operation, including hinge replacement, frame straightening, welding, track and roller work, operator repair, and control board replacement. It covers both manual gates and electric or automated systems. In San Clemente, the coastal environment means much of our repair work also involves treating or replacing corrosion-damaged hardware before it fails structurally. Call (866) 282-7403 and describe what’s happening, and we’ll tell you what’s likely wrong and what it’ll take to fix it.
Most residential gate repairs are completed the same day we arrive, usually within one to two hours for common failures like a hinge swap, limit adjustment, or latch replacement. More involved work like welding in new frame sections or replacing a commercial operator motor may require half a day or scheduling a follow-up for parts. We carry parts for the brands we service, which is why our repair times run faster than a generalist who has to order and wait. We’ll give you a time estimate with your written quote.
Most San Clemente gate repairs cost between $150 and $450, with electric operator and control board repairs landing between $300 and $900. Structural welding and frame work typically runs $200 to $600. Your exact price depends on the gate type, the system brand, and what specifically failed, and we’ll quote it in writing before any work begins. Estimates are free, and there’s no charge to call and ask what your symptoms point to.
Yes. We service nine gate and operator brands: Ghost Controls, DoorKing, Mighty Mule, Elite, LiftMaster, FAAC, BFT, Linear, and Viking. That spans entry-level residential openers through professional-grade commercial systems. We carry brand-correct parts and know the specific failure modes of each system, so you’re not paying for us to learn on your gate. If your gate uses a brand you don’t see listed, call and ask, we’ll likely still be able to help.
Yes. A gate stuck open is a security problem, and a gate stuck closed means you can’t get your car out. In San Clemente and the surrounding communities, we respond to emergency gate failures as quickly as possible, often the same day. If your gate won’t move and you need it working today, call (866) 282-7403 and tell us what’s happening, and we’ll get a technician routed to you.
We stand behind the repairs we do. Parts are covered by their manufacturer warranties, and our labor has its own workmanship warranty. If something we repaired fails because of our work, we return and make it right without charging you again. When you get your quote, ask us about the specific warranty that applies to your repair. We’re a local San Clemente company, and our reputation depends on gates that stay fixed.
Clear the area around the gate so we have working room on both sides, and if you have an electric gate, locate the operator and any keypad or intercom systems you use. Move vehicles away from the gate’s travel path so we can test full cycles safely. If you have a swing gate, make sure nothing is stored within the swing radius. That’s all you need to do, we handle the rest from truck to test.
Schedule Your Gate Repair Service in San Clemente Today
A gate that isn’t working is a gate that isn’t securing your property. Call (866) 282-7403 now for a free, no-obligation estimate from a San Clemente gate specialist who knows your brand before the truck even rolls. We’ll diagnose over the phone, quote in writing, and get your gate back to working before you know it.
Written by Oscar Jarvis, Owner at Gate Repair San Clemente, serving San Clemente and South Orange County.